THAI SUPPORT ENGINEERING
เมษายน 19, 2014, 03:52:20 am *
ยินดีต้อนรับคุณ, บุคคลทั่วไป กรุณา เข้าสู่ระบบ หรือ ลงทะเบียน

เข้าสู่ระบบด้วยชื่อผู้ใช้ รหัสผ่าน และระยะเวลาในเซสชั่น
ข่าว: SMF - Just Installed!
 
   หน้าแรก   ช่วยเหลือ ค้นหา เข้าสู่ระบบ สมัครสมาชิก  
หน้า: [1]
  ส่งหัวข้อนี้  |  พิมพ์  
ผู้เขียน หัวข้อ: SURFACE PREPARATION STANDARD  (อ่าน 13524 ครั้ง)
0 สมาชิก และ 1 บุคคลทั่วไป กำลังดูหัวข้อนี้
Support@Peak
เปลี่ยนตัวเราด้วยลมหายใจของเราเอง
จอมยุทธท่องยุทธจักร
ทารกน้อยจิ๋วแป๊ะทง
*****
กระทู้: 49



« เมื่อ: เมษายน 10, 2010, 12:13:41 am »

การทำสีให้เกิดประสิทธิภาพสูงสุด ... สิ่งที่เป็นหัวใจก็คือ การเตรียมพื้นผิวก่อนการทำสีให้ดีที่สุด เท่าที่จะทำได้ ข้อมูลของการเตรียมพื้นผิว ตามมาตรฐานต่างๆ

SURFACE PREPARATION STANDARD

1. National Association of Corrosion Engineers (NACE)
2. Steel Structures Painting Council (SSPC)
3. Swedish Standards (Sa,St)

--------------------------------------------------------------------------------
SSPC-SP-1

Solvent Cleaning - Removal of all detrimental foreign matter such as oil, grease, dirt, soil, salts, drawing and cutting compounds, and other contaminants from steel surfaces by the use of solvents, emulsions, cleaning compounds, steam or other similar materials and methods which involve a solvent or cleaning action.


--------------------------------------------------------------------------------

SSPC-SP-2
St 2
Hand Tool Cleaning - Removal of all rust scale, mill scale, loose rust and loose paint to the degree specified by hand wire brushing, hand sanding, hand scraping, hand chipping or other hand impact tods or by a combination of these methods. The substrate should have a faint metallic sheen and also be free of oil, grease, dust, soil, salts and other contaminants.


--------------------------------------------------------------------------------

SSPC-SP-3
St 3
Power Tool Cleaning - Removal of all rust scale, mill scale, loose paint, and loose rust to the degree specified by power wire brushes, power impact tools, power grinders, power sanders or by a combination of these methods. The substrate should have a pronounced metallic sheen and also be free of oil, grease, dirt, soil, salts and other contaminants. Surface should not be buffed or polished smooth.


--------------------------------------------------------------------------------

SSPC-SP-4
Flame Cleaning - Removal of all loose scale, rust and other detrimental foreign matter by passing high temperature, high velocity oxy-acetylene flames over the entire surface, followed by wire brushing. Surface should also be free of oil, grease, dirt, soil, salts and other contaminants.


--------------------------------------------------------------------------------

SSPC-SP-5
Sa 3
NACE 1
White Metal Blast Cleaning - Removal of all mill scale, rust, rust scale, paint or foreign matter by the use of abrasives propelled through nozzles or by centrifugal wheels. A White Metal Blast Cleaned Surface Finish is defined as a surface with a gray-white, uniform metallic color, slightly roughened to form a suitable anchor pattern for coatings. The surface, when viewed without magnification, shall be free of all oil, grease, dirt, visible mill scale, rust, corrosion products, oxides, paint, or any other foreign matter.


--------------------------------------------------------------------------------

SSPC-SP6
Sa 2
NACE 3
Commercial Blast Cleaning - Removal of mill scale, rust, rust scale, paint or foreign matter by the use of abrasives propelled through nozzles or by centrifugal wheels, to the degree specified. A Commercial Blast Cleaned Surface Finish is defined as one from which all oil, grease, dirt, rust scale and foreign matter have been completely removed from the surface and all rust, mill scale and old paint have been completely removed except for slight shadows, streaks, or discolorations caused by rust stain, mill scale oxides or slight, tight residues of paint or coating that may remain; if the surface is pitted, slight residues of rust or paint may by found in the bottom of pits; at least two-thirds of each square inch of surface area shall be free of all visible residues and the remainder shall be limited to the light discoloration, slight staining or tight residues mentioned above.


--------------------------------------------------------------------------------

SSPC-SP-7
Sa 1
Brush-Off Blast Cleaning - Removal of loose mill scale, loose rust, and loose paint, to the degree hereafter specified, by the impact of abrasives propelled through nozzles or by centrifugal wheels. It is not intended that the surface shall be free of all mill scale, rust, and paint. The remaining mill scale, rust, and paint should be tight and the surface should be sufficiently abraded to provide good adhesion and bonding of paint. A Brush-Off Blast Cleaned Surface Finish is defined as one from which all oil, grease, dirt, rust scale, loose mill scale, loose rust and loose paint or coatings are removed completely but tight mill scale and tightly adhered rust, paint and coatings are permitted to remain provided that all mill scale and rust have been exposed to the abrasive blast pattern sufficiently to expose numerous flecks of the underlying metal fairly uniformly distributed over the entire surface.


--------------------------------------------------------------------------------

SSPC-SP-8
Pickling - Removal of all mill scale, rust and rust scale by chemical reaction, or by electrolysis, or by both. It is intended that the pickled surface shall be completely free of all scale, rust, and foreign matter. Furthermore, the surface shall be free of unreacted or harmful acid or alkali, or smut.


--------------------------------------------------------------------------------

SSPC-SP-9
Weathering Followed By Blast Cleaning - Weathering to remove all or part of the mill scale followed by one of the blast cleaning standards.

SSPC-SP-10
Sa 2-1/2
NACE 2
Near-White Blast Cleaning - Removal of nearly all mill scale, rust, rust scale, paint, or foreign matter by the use of abrasives propelled through nozzles or by centrifugal wheels, to the degree hereafter specified. A Near-White Blast Cleaned Surface Finish is defined as one from which all oil, grease, dirt, mill scale, rust, corrosion products, oxides, paint or other foreign matter have been completely removed from the surface except for very light shadows, very slight streaks or slight discolorations caused by rust stain, mill scale oxides, or light, tight residues of paint or coating that may remain. At least 95 percent of each square inch of surface area shall be free of all visible residues, and the remainder shall be limited to the light discoloration mentioned above.

credit : www.misterpainting.com
บันทึกการเข้า

อดีตเป็นแค่ลูกชาวนา ปัจจุบันคือคนสามัญ อนาคตตอบแทนคุณแผ่นดินเกิด
หน้า: [1]
  ส่งหัวข้อนี้  |  พิมพ์  
 
กระโดดไป:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2006-2009, Simple Machines | Thai language by ThaiSMF Valid XHTML 1.0! Valid CSS!